Where Not to Use

DO NOT use on vertical surfaces or areas subject to hydrostatic pressure. NOT for industrial use or areas subject to forklifts.

Preparation

• All surfaces must be clean, sound, dry and free of any dirt, oil, and grease.

New and Uncoated Concrete or Masonry Surfaces:

• Allow new surfaces to cure 30 days.
• Clean and etch surface using a product such as a muriatic acid etcher (read and follow all manufacturer's label directions) to achieve a textured profile similar to 150 grit sandpaper.
• Wipe your fingers over the clean, dry floor to check for dust or powder.
• Ensure there is no residue on your fingers that may have been left from the etcher. If residue is found, rinse the surface to remove residue.
• Allow the surface to dry completely.
• Sprinkle a few drops of water onto the surface. If water is quickly absorbed and the surface feels like 150 grit sandpaper, the surface is ready. If not, re-etch.

Painted, Stained or Sealed Concrete:

• For a painted surface in sound condition, use a product to clean and prepare the surface.
• If the coating is failing or peeling, use a paint stripper to remove old coating or scrape/sand down to a sound concrete surface.
• Scuff sand glossy surfaces.
• Clean and spot etch any exposed concrete.
• Remove all dust with a damp cloth, allow to dry.

Prime

Optimize topcoat adhesion by priming with BEHR PREMIUM® No. 880 Concrete & Masonry Bonding Primer for areas subject to automotive tires, heavy foot traffic, or persistent exposure to moisture, or in areas previously treated for efflorescence or laitance.

Application

• DO NOT THIN. Intermix all cans of the same product to ensure color uniformity. Stir before and occasionally during application.
• Use product when air and surface temperatures are between 50-90° F.
• Apply to dry concrete. Do not apply if rain or heavy dew is expected within 24 hours.
• Do not apply in direct sunlight.
• To begin application, tape off any adjacent areas and apply directly from container to the edges, corners, and joints using a nylon/polyester brush.
• Fill hairline cracks up to 1/8" with coating using a brush. Deeper cracks may need multiple fills to level with surface. Allow to dry completely before roller application.
• For roller application: after cutting in the edges, pour a 12" strip, about 3" wide, directly to surface. For smaller areas, pour a strip about 3"-5" long, about 3" wide. NOTE: Avoid over application to prevent cracking, peeling, and reduced spread rate.
• Using a 1/4" adhesive roller cover, apply moderate pressure and roll in multiple directions to evenly distribute in 3’ x 3’ sections.
• Avoid regular painting patterns and knock down hard edges using the roller.
• Work quickly and overlap the previously coated areas to ensure full coverage.
• The first coat will act as the base coat, and it will not completely cover the surface by design.
• Allow first coat to dry then apply second coat in the same method as the first coat.
• While two coats are necessary, additional coats may help hide previous surface imperfections or cover over contrasting colors.
• Spray application: For larger projects, consider using a texture sprayer with a 4mm tip.
• Spray in 4' x 4' sections. Back roll first coat. 2nd and/or final coat back roll is optional.
• Soap & water clean-up.

Touch-Ups

• An annual touch-up may be required in areas subject to automotive tires or heavy traffic.
• Clean touch-up area with power washer or scrub brush.
• For small touch-up areas, use a nylon/polyester brush.
• For larger touch-up areas, use ¼" adhesive roller cover.
• Feather out product in multiple directions, slightly overlapping previous coating.
• Allow to completely dry and repeat steps as needed.
• NOTE: Once dry, touch-up area will likely have higher sheen.

Dry Time

• Longer dry time required in cooler temperatures and in higher humidity.
• The floor may be subjected to light foot traffic after 24 hours.
• Allow 72 hours before subjecting surface to automotive tires, heavy foot traffic or repositioning furniture.
• Premature heavy traffic will cause paint failure requiring spot recoating.
• Wait at least 30 days before rinsing or cleaning. Use a mild detergent as needed.
• Abrasive cleaners and pressure-washers should be used carefully to avoid premature coating failure.

Clean Up

• Soap & water clean-up.
• Wait at least 30 days before rinsing or cleaning.
• Use a mild detergent as needed.
• Abrasive cleaners and pressure-washers should be used carefully to avoid premature coating failure.

Disposal

• Properly dispose of all soiled rags.
• To recycle or properly dispose of product in your community, contact your household refuse collection service.