BEHR DYNASTY^® Exterior Semi-Gloss

Avg. Rating:

BEHR DYNASTY Exterior Semi-Gloss Paint delivers 10-Year Color Fade Protection for the exterior of your home. Your home will look freshly painted longer, even under the most challenging weather conditions.

FOR TINT BASES – DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS

*Valid only when tinted to colors from the BEHR DYNASTY® specially curated Exterior Color Fade Protection Palette. Based on predictive lab testing with a color shift less than Delta E of 5 as measured by CieLAB. A primer coat may be needed. Two coats of BEHR DYNASTY® Exterior Paint are recommended for optimal durability. Individual results may vary. See back label instructions for details and warranty limitations.

Finish

A Semi-Gloss paint sheen is a sleek, radiant sheen that creates a hard, durable finish. It is formulated to withstand wear, and will also resist moisture, fading and stains.

Best For Use In

Doors, trim and shutters; Exterior furniture. Do not use on floors.

Coverage

250-400 Sq. Ft. per Gallon

PRODUCT USAGE

1 HR Dry Time
2 HR Recoat Time
250-400 Sq. Ft.
Coverage per Gallon
Soap & Water
Clean-Up
Protect
from Freezing

Where to Use

Use on properly prepared and cleaned coated and uncoated Exterior surfaces. Protection for Wood, Vinyl, Aluminum, Fiber Cement Siding, Metals, Brick, Masonry, Stucco, Steel and Fences. Do not use on floors.

Preparation & Prime

Use on properly prepared and cleaned coated and uncoated Exterior surfaces. Countersink nailheads, fill and sand smooth. Remove rust, loose or peeling paint. Repair imperfections and sand smooth.
Wash off dirt, grease and chalk with detergent and/or power wash. Remove mildew stains with a mildew stain removing product.
Clean and sand new or weathered wood. Scuff sand or degloss smooth or glossy surfaces.
Scuff sand or etch metals. Rinse and allow to dry.
Caulk windows, doors and other openings.
Allow new stucco, plaster and masonry to cure for 30 days before painting.
Use BEHR DYNASTY paint as a primer for repaired or uncoated surfaces, including woods that contain tannins and heavily stained areas (two primer coats required for redwood and cedar). Lock in stains with the first primer coat; if necessary, apply a second primer coat of BEHR DYNASTY.
For drastic color changes or when applying deep colors denoted with a dagger (†) on the color chip, apply a tinted primer coat of BEHR BEHR DYNASTY, if needed.

Application

Apply product on dry substrates when air and surface temperatures are between 35°-90°F (2°-32°C) and will remain between 35°-90°F (2°-32°C) for at least 4 hours after applying.
Allow paint film to dry for at least 60 minutes prior to rain showers when temperatures are between 60°-70° F (15°-21° C) and 60-70% relative humidity. Lower temperatures, higher humidity or deep colors may increase dry time and/or rain resistance time.
Stir paint occasionally. Intermix containers of same product to ensure color and sheen uniformity.
On semi-smooth surfaces, use a high quality 3/8-1/2" nap roller cover, nylon/polyester brush or an airless sprayer (.015 -.021" spray tip, 60 mesh filter).
On rough surfaces, use a high quality 3/4-1" nap roller cover.
Do not thin if using a roller or brush; however, if using a sprayer and thinning is required, thin with water at a rate of no more than 1/2 pint per gallon.
On heavy stains and woods that contain tannins, allow 12-16 hours of dry time between coats.
After 4 weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent. Dry paint film is mildew resistant.
When applying to vinyl, color choice must be the same color or lighter than the existing color.
Do not use on floors.

Disposal

For disposal of empty containers, unused paint and soiled rags, contact your household refuse collection service.

Compare Behr Sheens

Stucco / Masonry / Brick
Siding ( Aluminum / Fiber Cement / Wood / Vinyl )
Doors / Windows / Shutters
Garage Doors / Gutters
Soffit / Fascia / Eaves

BEHR DYNASTY^® Exterior Flat Learn More

BEHR DYNASTY^® Exterior Satin Learn More

BEHR DYNASTY^® Exterior Semi-Gloss Learn More

SDS AND DATA SHEET

BEHR DYNASTY^® Exterior Semi-Gloss

Ultra Pure White No. 5650 Deep Base No. 5653 Medium Base No. 5654

See Full SDS, Product Data & Safety

WARRANTY

Behr Process LLC warrants to the original residential consumer purchaser (“you”) the performance of this product as described on this label for so long as you own and reside in the home, subject to the exceptions outlined below. THIS WARRANTY IS NOT VALID IF THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE AND USED AND CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, subject to the exceptions outlined herein, Behr Process LLC will, at its sole option and upon presentation of proof-of-purchase (i.e., the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. NOTWITHSTANDING ANYTHING IN THE FOREGOING, THIS WARRANTY DOES NOT APPLY TO OR COVER BEHR DYNASTY 10-YEAR COLOR FADE PROTECTION AND RELATED DESCRIPTION ON THIS LABEL. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental, consequential, or punitive damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental, consequential, or punitive damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. To obtain warranty service, call 1-800-854-0133. Behr Process LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

To consult with a Behr Paint Company Representative, call 1-800-854-0133 Ext. 2 (U.S.A. only).